In this detailed guide I will tell you how to do it.SauberBathtub gardens that don't work! As you know, hot tubs are a popular choice for those looking to add the benefits of soaking to their lives.
They help soothe sore muscles, provide comfort and relaxation, and even offer their owners a bit of luxury. However, like everything else, bathtubs need a deep cleaning from time to time.
Especially the jets, a source of relaxation in hot tubs, can score pointsdirtyover time. They may even start to produce a black substance that is potentially harmful.
Now that we understand the importance of keeping your bathtub jets clean, how do you do it effectively? With this guide, you can take your bathtub jets from looking dodgy and gross to a complete clean in no time.
How to clean bathtub jets that don't work
make preparations
While there are other cleaning apps where you can grab your rubber gloves and a cleaning spray, this isn't one of them. It is important to do the proper preparation before you start cleaning.
For one, you need to make sure that the water temperature and level are just right for the cleaning products you use to work at their best.
In addition, you need to know how to adjust the valves of the jet so that you can not only clean it, but also disinfect it. Just because you can't see those hard-to-reach places doesn't mean they don't get gross.
fill the tub
The first thing to do in preparation for cleaning your bathtub jets is to make sure you have enough water in the bathtub.
Detergents are most effective when the water is as hot as possible, so make sure you have enough in the tub to get the job done.
If you use too little water, you may not be able to completely sanitize the tub. Without proper disinfection, you can find soap scum, mold, biofilm, and all manner of other contaminants reappearing sooner rather than later.
Fill the tub so that the water level is above the top of the jets. This allows detergent and water to pass through the entire nozzle system. You can then effectively attack contaminants that may enter the tub and through the spouts.
Turn off the air inlet valves.
Now that your hot tub is full of water, it's time to take care of the inlet valves. Hot tubs have a complicated system consisting of multiple valves.
These valves allow you to control how the water circulates and tell the tub how much air to inject into the jets.
By closing the air inlet valves, you ensure that only water flows during cleaning. Plus, it creates a closed loop, so you can sanitize the tub with whatever cleaner you use to get the job done.
Just be sure to read the instruction manual if you are not completely familiar with the features of the air intake setup.
For the most part, you can close these valves by turning them clockwise, but there are some tubs that have other functions.
add the cleaner
With the tub ready to go, you are now ready to mix your cleaner so you can properly clean the jets. There are two ways to do this.
You can purchase a bathtub cleaner designed specifically for this purpose. You can also get this cleaner from the bathtub manufacturer.
This way, you can ensure that you have the right cleaner for the job at hand. However, some people aren't thrilled with the chemicals used in cleaning products like these and choose an alternate route.
You can also create a DIY cleaner with somewhiteningor vinegar. The bathtub needs something strong that will scrub the internal components and sanitize, absorb and remove these hazardous materials from the bathtub.
A great DIY recipe includes dish soap for its cleaning benefits, while chlorine bleach will kill any contaminants that may be lodged in the nozzles.
Vinegar is also a great option, as it is a very versatile household cleaner. Some people may prefer to use vinegar instead of bleach, as it is an organic alternative. Your mixture should be ¼ cup of dish soap, liquid or powder works well.
Mix it with a cup of vinegar or bleach and you can even add some essential oils for better smell and aromatherapy benefits. All you have to do is pour the mixture into the tub.
For acrylic tubs, be sure to rotate it to properly distribute the cleaner throughout the system. Wait a few minutes for it to effectively dissolve in the water before moving on to the next step in the process.
circulation of the solution
Cleaning a hot tub is quite similar to cleaning an above ground pool. For both, put the detergent in the tub.
The good news is that while other cleaning methods involve scrubbing, you can let the nozzles do all the work for you. When the jets are activated, they move the cleaner through the tub and into the tub.
This helps the cleaner attack dirt and any other contaminants that may be lodged deep in the spouts and other tub crevices. Turn the tub jets on high and let them run for about 15 minutes.
If the water turns dark, it's perfectly normal, so don't panic. This is a good sign that the cleaner has started to remove and killSchimmel, mold and all kinds of dirt and grime.
When you're sure the jets have done their due diligence, you can turn them off again. From there, you want to drain the water and any cleaner residue left behind when draining the water.
Use Baking Soda for Rust
Depending on the age of your bathtub and the maintenance it has done, you may have to deal with some rust on the faucet and other metal components.
The jets may be clean, but you also want to clean the entire tub. Some contaminants can burrow deep into cracks, especially rusty areas.
They can even survive previous cleaning attempts if you don't do them justice with a bit of cleaner and a brush. Fortunately, baking soda is effective in fighting rust.
All you have to do is mix ¼ cup of baking soda with 1 cup of white vinegar and pour into a spray bottle. From this you will eventually get a paste mixture, which should then be applied to the areas with rust.
You can use a scrub brush or old toothbrush to get into those hard to reach areas and remove the rust. Be sure to rinse everything off with lukewarm water when you're done.
The rust should be gone and the dirt that was hiding underneath should be gone as well.
Re-add cold water to the tub.
When you feel like all the rust has been removed, you are entering the home stretch of the cleaning process. There may be residue from the cleaner you used.
You don't want to soak up that cleaning residue, so it's time to rinse it all out. A good dose of cold water can do a lot of good here.
By rinsing your tub with cold water, you can remove both detergent residue and any remaining residue, keeping your tub not only clean but completely sterile.
Simply fill your hot tub with cold water until all the jets are fully submerged. Once again, let the jets do the work. Turn them on and let them rise for about 15 minutes.
After 15 minutes, drain the water again. You should be looking at a completely clean bathtub. All that's left is to jump in and enjoy the relaxing benefits a hot tub has to offer.
The process is very easy and should be done from time to time to ensure that your jets (and the rest of your tub) remain clean and sterile.
Diploma
Now that you know how to clean non-functioning bathtub jets, your hot tub can come in very handy. And for all it gives you, it helps to give it back every once in a while by doing a deep cleaning.
The best part is that you don't have to get on your knees and scrub to clean it. With a little homebrew, you can let the jets do all the work for you. What's left is a frothy vat that you can plunge back into.